Home > Tank Testing Equipment > Other Testing Equipment

Other Testing Equipment

ATS offers a wide array of other premium testing equipment for environmental compliance.

Vapor Coupler Test Assembly

Conduct pressure decay testing according to California Environmental Protection Agency Air Resources Board (CARB) Vapor Recovery Test Procedue TP-201.3 with this easy to use Vapor Coupler Test Assembly.

Test phase 1 vapor poppets (dry brakes)
Perform pressure decay
Easy cam lock attachment
1 psig pressure relief valve
Easy quick connect with tube for digital manometer
Quick connect with ball valve for regulated nitrogen

Dimensions: 15″ x 6″ diameter
Weight: 8 lbs.

Vapor Recovery Panel

Easy to carry multi-functional vapor recovery CARB test panel. Basic and simple to use. Meets CARB specs for TP-91-1, TP-91-2, static pressure, dynamic back pressure, and liquid blockage. This is the best unit out there.

Perform dynamic back pressure and liquid blockage all in one panel
All stainless steel construction- will not rust!!
Easy to carry
Easy to read gauges
Quick connect with ball valve for regulated nitrogen
Easy to read flow meter

Dimensions: 20″ x 20″ x 9 3/4″
Weight: 29 lbs.

Extractor Easy Out

A dual purpose, easy to use extractor easy out tool.

Remove seized ball float overfill valves!
Easy installation of extractor plugs for pressure decay or tank testing
Locking mechanism to keep ball floats from dropping
Strong, durable construction
Can be used with any wrench

Dimensions: 66″ x 3″ diameter
Weight: 28 lbs.

Pressure/Vacuum Vent Cap Tester

Perform pressure/vacuum vent cap tests according to CARB TP201.1E and new federal Stage 1 regulation 40 CFR 63 Part CCCCCC with this easy to use vent cap tester.

Test leak rate and cracking pressures
Black anodized aluminum rotometers
Magnifier lens for enhanced reading resolution
Lightweight and easy to cary
Quick connect with ball valve for regulated nitrogen and digital manometer

Dimensions: 8″ x 10″ x 16″
Weight: 4 lbs.

Fill Adapter Chain Wrench

Remove any standard/swivel fill adapter or dry brake with this durable chain wrench.

Remove fill adapters and dry brakes in hard to reach places with limited room
Fits any fill adapter or dry brake
Strong durable construction for use with any wrench

Dimensions: 50″ long
Weight: 10 lbs.

Intrinsically Safe Vacuum Pump

Eliminate the need for inert gasses and cut your on-site testing time by 20% with this intrinsically safe vacuum pump.

110 VAC motor
Positive displacement lobe vacuum pump
Intrinsically safe
Sits on portable cart

See the spec sheet.

ATEK Tank Cleaning Pump

Clean your underground storage tanks the effective way. This portable system is a durable work horse that gets the job done right.

1 ½" SPARK FREE diaphragm pump
Large 150 micron nylon bag filter and housing
Adjustable flow rate
1 ½" fuel hose

See the spec sheet.

Leak Detector Tester

Calibrate and test the functionality of any leak detector with this easy to use leak detector tester.

Test both mechanical and electronic line leak detectors
Calibrate a 3 gph leak with its highly sensitive needle valve
Easy to read gauge
Graduated cylinder for measuring resiliency

Ultrasonic Thickness Gauge

Make your UT testing experience easy with this single-crystal delayed probe, precise ultrasonic thickness gauge.

Two operating modes: I-E (interface-echo) and E-E mode (echo-echo)
Multi-echo is used to enhance the accuracy with the resolution of 0.0001 and the low limit of 0.012
Multiple unit selection in inches or millimeters
Handheld and lightweight at less than &fract12; lb

See the spec sheet.

Water Sensor Calibration Fluid (E & D Cal)

No need to try to explain why you’re putting water into your customer’s tank anymore. This new water sensor calibration fluid will put everyone’s mind at ease.